Error code
Oven error code F1 06
DCS oven error code F1 06: The most useful entry in the whole table, because it is almost never a failure — it is a mismatch. Which machines can raise it, what the maker publishes about it, and what to do next.
- From $95 diagnostic, credited to the repair
- 59 cities and neighborhoods covered
- OEM parts available on order
- In writing the price, before anything is opened
What we can confirm
Code F1 06, from the manufacturer's own documentation
A code is only meaningful together with the machine showing it — the same digits mean different things on different equipment.
The code
F1 06
The most useful entry in the whole table, because it is almost never a failure — it is a mismatch. The two boards each carry an idea of which oven they are in, and this code says they disagree. That happens when a replacement part has gone in from the wrong variant, or when a board has been fitted without its model identity being set. The important consequence: no amount of further replacing will clear it. If this code appeared after a repair, the repair is the cause, and the cure is matching the identity rather than buying another board.
or call (305) 526-4714
What it narrows down to
The clock board does not support the model identity set on the power board.
Diagnostic
From $95, credited to the repair
On the same appliance
What else belongs to the wall ovens
On this make a code belongs to the appliance rather than to a product line. These are the other conditions this machine can display, and the models that can show this one — a display often has more than one thing to say, and the model number decides what any of it costs to put right.
Other codes this appliance can display
The control cannot see the master power board at all.
The control cannot see the slave power board.
A general software error inside the control.
Communication with the master board has failed.
Communication with the slave board has failed.
An error icon lights on the panel and the machine beeps when the door is opened.
The same digits mean different things on different equipment. Search the full code list
In more detail
About Oven error code F1 06
What F1 06 means on this make
The most useful entry in the whole table, because it is almost never a failure — it is a mismatch. The two boards each carry an idea of which oven they are in, and this code says they disagree. That happens when a replacement part has gone in from the wrong variant, or when a board has been fitted without its model identity being set. The important consequence: no amount of further replacing will clear it. If this code appeared after a repair, the repair is the cause, and the cure is matching the identity rather than buying another board.
Where this appears, and which table it belongs to
On the appliance's own display. Photograph it before you cut the power: a display that has been cleared has taken the evidence with it, and there is no way to ask the machine for it again. Then check the model, because this make changed hands in 2016 and the two generations share no code string. The same characters mean different things on a Classic ERC oven, an ER-series range and a Modernist induction cooktop, and a meaning read off the wrong table is worse than no meaning at all.
Which machines this one applies to
wall ovens carrying the decoded F-series table. The same number on a different appliance of this make is a different page and often a different repair, which is why this archive is organized by appliance rather than by number. This maker documents codes on 4 of the appliance types this site publishes — bbq grill, cooktop, oven and range — and publishes none at all for bbq grill, beverage center, outdoor kitchen appliance, range and range hood. Those appliances have symptom pages here and no code pages, which is the honest answer rather than borrowing a table from the machine next door.
What to do about it
- Say whether a part has been replaced in this oven recently, and by whom. This code almost always follows one.
- Do not order a second board. A mismatch is not cured by adding another mismatched part, and this is where money gets spent for nothing.
- The identity set on the replacement has to match the machine. That is configuration work, and it is quick once somebody knows that is what they are looking at.
Where this goes next
The job this usually becomes is diagnostic visit, and that page carries a starting figure and the reasons that move it. If it turns out to be nothing — and on this make a real share of these are modes, reminders and settings rather than problems — the visit ends there and you pay the diagnostic and nothing else, or call (305) 526-4714 and describe what the panel is doing before booking anything.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards